Software Specifications

Standard Compliance

• IEEE 802.3 and 802.3u 10Base-T and 100Base-TX physical layer specification
• IEEE 802.11g specification compliance for wireless LAN
• IEEE 802.11b specification compliance for wireless LAN
• IEEE 802.1x security standard support
• Power over Ethernet, IEEE 802.3at compliant

Operating Mode

• Thin AP mode
• Fat AP mode

Thin AP

• FIT AP zero configuration
• DHCP option43,60
• DHCP detection
• DNS detection
• Static IP detection

Multiple BSSID

• Support up to 16 SSID Profile setting
• Support up to 4 Strict Priority Queue at least and configuration of certain SSID corresponding to Strict Priority Queue so as to distinguish link service priority
• Limitation of client connections (# is configurable, default: unlimited)
• Bandwidth control

Spanning Tree Protocol

• 802.1d support

DHCP Client

• Ability to act as a DHCP client to get IP address from DHCP server from LAN port
• In DHCP client mode, if DHCP server is not available, then use default IP address

VLAN

• Support per SSID VLAN tagging
• Support system VLAN tagging

VPN pass through

• IPSec, PPTP and L2TP pass through support
• Support in AP and WDS modes, but not in client mode

Transmit Power Adjustment

Manually adjustable

• Transmit power adjustable unit should be 1dBm
• Transmit power adjustable range should be at least 8dB

Device Remote Management

• Support remote management via SSH, FTP, WWW, and SNMP
• Administrator can specify the following method to allow for device management: Interface (WLAN or Ethernet) / MAC address

System Monitoring

• System status

Management

• Embedded Web Configuration management
• Command-line interface: SSH support
• FTP/Web for firmware downloading and configuration backup and restore
• Built-in Diagnostic Tool
• SNMP Management (v1, v2C, C3)

Security

• MAC address filtering through WLAN (support 128 account)
• IEEE 802.1x security (EAP-TLS, EAP-TTLS, PEAP, EAP-SIM, FAST, -AKA) 64/128-bits WEP
• Both WPA/WPA2 PSK & Enterprise support
• Mixed WPA& WPA2 mode (support both WPA and WPA2 clients)

Quality of Service

• WMM support

Diagnostics Capabilities

The access point can perform self-diagnostic tests. These tests check the integrity of the following circuits:

• FLASH memory
• DRAM
• Ethernet port
• Wireless port

Sys log:

• Error log
• Trace log
• Packet log

Association Management

• 11n Priority: 802.11n standard gets a higher association priority than 802.11b/g standards
• Support Air Time Fairness for clients compliant to different standards of 802.11b/g/n
• Support the setting of automatic Disassociation with low-level MCS users

Integrated Spectrum Analyzer

Ability to detect interference source and avoid interference by automatically selecting the best channel:

• Ability to detect WLAN Devices Interference
• Ability to detect Non WLAN Devices Interference

Newly-added MIB Nodes

wlanStationTable:

• SNR (Signal-to-Noise Ratio) of STAs associated to AP should be measured in dB
• Physical layer Transmit Rate of STAs associated to AP
• Packet Error Ratio of STAs associated to AP

wlanStatisticTable:

• Co-Channel Interference, CCI
• Adjacent Channel Interference, ACI
• WLAN Devices Interference
• Non WLAN Devices Interference

Physical Specifications

• Dimension: 213 (L) mm × 170(D) mm ×39 (H) mm

• Weight: 500g

 Environmental Specifications

• Operating Temperature: 0 to 50°C (device) / 0 ~ 40°C (power adapter)
• StorageTemperature: -10 to 55°C (device) / 20 to 90% RH (power adapter)
• Operating Humidity: 15 to 90% RH (device) / -20 ~ 85°C (power adapter)
• Storage Humidity: 15 to 90% RH (device) / 20 to 95% RH (power adapter)
• Safety: EN 60950-1_2006+A11:2009
• EMI European Union (CE mark): EN 301 489-1 V1.8.1_2008-04 / EN 301 489-17 V2.1.1_2009-05
• EMI North America: FCC Part15.107_2008-07
• Wireless European Union: ETSI EN 300 328 V1.7.1_2006-10
• Wireless North America: FCC Part 15.247, 15.407_2008-07